03 05 00

No. 010

Related Content: LEED Credit Chart Spanish Data Sheet Request Brochure MSDS

BELLATRIX

Premium Concrete Enhancer

DESCRIPTION
BELLATRIX is formulated using dual-protection technology combined with unique hybrid polymers, to offer the ultimate in concrete protection. Proprietary, dual-action technology provides the ultimate in both penetrating and film-forming concrete protection. BELLATRIX offers environmentally friendly, VOC-compliant protection, which provides increased stain suspension and resistance against most contaminants found in kitchens, retail food stores, restaurants, malls, garages, warehouses, distribution centers, etc.

USES
While originally formulated to be used in conjunction with hardened concrete floor systems, such as W. R. MEADOWS LIQUI-HARD® and the INDUROSHINE™ polished concrete system, BELLATRIX may also be utilized anywhere a clear, high-gloss, dual-action concrete protection system is desired.

PACKAGING
1 Gallon (3.79 Liter) Units/4 per carton
5 Gallon (18.93 Liter) Pails
55 Gallon (208.20 Liter) Drums

COVERAGE*
500 – 1000 ft.²/gal. (12.27 – 24.54 m²/L)
*Coverage will vary due to texture, porosity and condition of the concrete.

TECHNICAL DATA (TYPICAL)**
The following results were obtained under laboratory conditions:

Color (Wet):	Milky White
Color (Dried):	Clear/Transparent
Weight per Gallon, lb./gal:	8.46
pH:	7.31
VOC, g/L	57.6
Drying Time @ 73° F, 50% RH	1-2 hours***
Re-coat time:	2-6 hours
Foot Traffic:	4-6 hours
Wheel Traffic:	6-12 hours
Adhesion to Concrete:	Excellent
Ultraviolet light (UV) degradation tested to ASTM C 1315, 8.86:
Ultraviolet Resistance:	Non-yellowing
Chalk Resistance:	No chalking
Check/Peel Resistance:	No deterioration
**All technical data is typical information, and may vary due to test methods, conditions and operator technique. **Low concrete or air temperatures and/or high relative humidity will extend drying times.

STAIN BLOCKING
BELLATRIX is formulated to provide a reasonable amount of time for cleanup and removal of spills. Prior to that removal, BELLATRIX will provide a barrier to the following contaminants:

APPLICATION
BELLATRIX is designed for existing concrete and should not be used as a curing compound on freshly placed concrete. A small test patch application is always recommended. The test patch must be done using the same applicator (personnel), equipment, surface preparation, application technique, and at the same temperatures, relative humidity, airflow conditions, etc., that will exist at the time of the full-scale BELLATRIX application.

Surface Preparation …The surface must be thoroughly clean, dry and free of anything that will prevent BELLATRIX from bonding properly with the concrete. This includes, but is not limited to: bond breakers, release agents, coatings, oil, grease, un-neutralized acid stain, dirt, efflorescence, dust, etc.

Polished Concrete … BELLATRIX may be applied over concrete that has been previously treated with a densifier/hardener such as LIQUI-HARD and/or polished with a system like INDUROSHINE. Concrete must be a minimum of 28 days old before polishing with INDUROSHINE. Allow a minimum of 48 hours after a LIQUID-HARD treatment before applying BELLATRIX. Best results are obtained if the surface is burnished two hours after application of BELLATRIX. Use a high speed burnisher with a 3000-grit or hogs hair pad. If products or systems other than INDUROSHINE or LIQUI-HARD are used, a small test patch application is always recommended.

Existing Concrete … BELLATRIX should be used full strength on existing concrete (no dilution necessary). Concrete must be a minimum of seven days old before applying BELLATRIX. The concrete must be clean, dry and prepared, per Surface Preparation instructions above.

Mixing … Any separation in the container must be re-dispersed with gentle agitation prior to use. CAUTION: TO AVOID FOAMING, DO NOT MIX EXCESSIVELY.

Application Method ... An industrial sprayer, such as a Chapin 1949, with a 5916 spray nozzle (or equivalent), delivering 1/10th of a gallon per minute, is recommended. Application equipment must be clean, dry and free of any previously used materials. After initially spraying the product onto the surface, uniformly spread it with a micro-fiber applicator. The micro-fiber pad should be pre-wetted with BELLATRIX pror to use, and the product must not be allowed to dry before spreading is complete. Optimum performance is achieved with two (2) uniform coats. The second coat should be applied at a 90° (right) angle to the first coat, only after the first coat is thoroughly dry – typically six (6) hours after application, depending on temperatures and conditions. NOTE: Keep surface dry for a minimum of 48 hours after application; full stain blocking ability will not be effective until 72 hours after final application.

Cleanup … While BELLATRIX is still wet, equipment can be cleaned with soap and water. Once dried, the material can be removed with a solvent, such as xylene or toluene.

PRECAUTIONS
KEEP FROM FREEZING. Do not use BELLATRIX as a curing compound on freshly placed concrete. Due to occasional uncontrollable variations in concrete substrates, application error, etc., BELLATRIX may not block all staining materials in every instance. BELLATRIX is formulated to provide a reasonable amount of time for cleanup and removal of spills. Do not apply when air, material or surface temperatures are expected to fall below 40° F (4° C) within four hours of completed application. DO NOT MIX WITH ANY OTHER PRODUCTS.

Stain resistance and gloss will vary with changes in dilution ratios, coverage rates and with the nature of the substrate. A test area is recommended to verify that the desired appearance and performance is achieved with the intended use conditions.

HEALTH AND SAFETY
Direct contact may result in mild irritation. Inhalation may cause irritation of the respiratory tract. Refer to Material Safety Data Sheet for complete health and safety information.

SHELF LIFE (TYPICAL)
One year in original, unopened container.

This material last updated February 2009.